If after the wash cycle you take the clothes out and they’re still soaking wet with water dripping off — it’s a sign that the machine failed to spin or drain properly. In this article, we’ll cover 5 common causes for this issue, offer possible solutions, and share a few pro tips from our top technician. Book our washer repair service:
Reasons Why the Washer Leaves Clothes Wet
$25 OFF
with Online Application
Description and Troubleshooting of Problems
Washer Drum Is Not Spinning
When the drum isn’t spinning, water may partially drain, but clothes will remain wet. This may be caused by electronic issues or mechanical failure.
Possible reasons:
- Suspension or absorbers broken
- Motor is not working
- Door lock is not working
- Faulty speed sensor
- Faulty drain pump
Read more about the causes in our article: washer won`t spin.
Solution
- Check if the drum spins freely by hand when the machine is off
- During the spin cycle, listen carefully to the sounds of the motor. If it’s silent — this could indicate a technical fault. In this case, a technician visit is required: besides professional motor diagnostics, the belt, wiring, and tachometer will need to be checked. Some parts may need to be replaced
Pro Tip:
We strongly advise not to remove the rear panel and inspect the belt yourself, as this could void the warranty. You might accidentally damage the internal structure. It’s better to leave diagnostics to a professional.
Filter Is Blocked
Over time, the washer’s filter collects lint, pet hair, small objects, and the other debris. Once it’s too clogged, water starts draining slowly or not at all. As a result, clothes don’t get spun properly and remain soaked.
Solution
- Unplug the washer
- Locate the filter access door (usually at the bottom of the front panel)
- Place a basin or deep container underneath — water may spill out
- Open the access panel and gently unscrew the filter
- Remove all debris and rinse the filter under running water
- Use an old toothbrush to clean hard-to-reach areas
- Screw the filter back in tightly
- Run the spin or drain cycle — check if the water has drained and the spin works properly
Pro Tip:
After cleaning the filter, it’s a good idea to also check the drain hose for clogs. Sometimes debris that passes through the filter can build up in the bends of the hose and block proper drainage.
Wrong Washing Programme
Keep in mind that some washing modes do not include a spin cycle. For example, “hand wash,” “quick wash,” or “delicate wash.” Always check the manual for your specific washer model before starting a load. Also, it’s possible to accidentally disable the spin function when choosing a cycle.
Solution
Check the cycle settings before starting the wash:
- Make sure the spin function is enabled
- Pay attention to RPM settings — we recommend 800 RPM as an ideal setting for proper spin without putting extra wear on the machine
- If after the wash the clothes are still too wet, run an extra “Spin” cycle
Washer Plugged Into an Extension Cord
Extension cords can cause voltage drops, especially if they’re old. A washing machine is a large appliance and requires a stable power supply. Using an extension cord can result in power fluctuations that prevent the motor from reaching full performance.
Consequences:
- Interrupted electronics function
- Not enough power for the spin cycle
- Accelerated wear on internal components
Solution
We recommend plugging the washer directly into a grounded wall outlet. This is important for both performance and safety.
Loading Too Many Clothes
Overloading the washer directly affects spin quality. During the wash, clothes absorb water and become significantly heavier. If the drum is full at the start, the final load weight may exceed what the machine can handle. Key parts like the belt, motor, and other components aren’t built for that kind of stress, so the drum can’t spin at full speed — leading to poor water extraction.
As a result, water remains in the clothes due to low centrifugal force. In some cases, items may not spin at all and stay soaking wet.
Solution
- When loading clothes, make sure the drum is no more than ¾ full. You can use this simple rule: your fist should fit between the top of the drum and the laundry. This ensures there’s enough room for proper spinning and water circulation
- Avoid washing several heavy items at once (e.g., blankets, jeans, duvets)
- If you have a large load, split it into smaller batches
- Some washers have a load weight sensor — watch for that and don’t exceed the maximum load. Ideally, stay under 80% of the maximum capacity
Repair Cost
| Drum repairing or replacing | $200 – $280 |
| Filter cleaning or replacing | $230 – $350 |
| Replacing the suspension and absorbers | $260 – $380 |
| Belt or motor replacing | $230 – $370 |
| Door repairing or replacing | $240 – $350 |
| Speed sensor replacing | $220 – $340 |
| Drain pump cleaning or replacing | $280 – $360 |
The price for washing machine repair varies based on the brand, specific model, and how complex the issue is.
FAQ
OTHER ARTICLES
Contact Us For Any Washer Repair Service
No matter the issue with your washer, our skilled technicians are ready to fix it. We guarantee prompt, dependable, and top-notch service. Simply call us or complete the form on our website to schedule a convenient repair time.
Call us today: (863) 594-1784
or fill out the form and we will contact you ourselves.
For some time now, I’ve been a content manager at TEODOR APPLIANCE REPAIR. I enjoy optimizing content and visualizing it on the website’s pages. My role is mostly unnoticed by most clients, but it’s appreciated by my management, which motivates me to create high-quality content!
6 Comments
Hi! I’m having a problem with the spin cycle. The washer only spins properly when I load a very small amount of laundry — no more than 1/3 of the drum. In all other cases, the clothes come out soaking wet. Can you tell me what the issue might be?
Hi Logan! Thanks for reaching out! That sounds like an issue with unbalanced load detection or a failing suspension system. Modern washers may skip the spin cycle if the load is uneven or too heavy, especially if the shock absorbers or suspension rods are worn out. We recommend scheduling a diagnostic — we’ll inspect the suspension, balance sensor, and spin function in detail.
I already had a technician from another company check my washer. The issue is — clothes are still floating in water after the wash. He told me the machine isn’t repairable, but I’m not confident in his opinion. I need urgent help. Can you come out for a diagnostic in the next few days?
Hi Chase! Absolutely — we’d be happy to take a second look. Sometimes machines are misdiagnosed or can still be fixed with the right parts. If the clothes are still sitting in water, it could be a faulty drain pump, clogged filter, or electronic issue. Please give us a call or book online: https://appliancerepairteodor.com/contacts/
We’ll do our best to fit you in within the next couple of days.
My washer only failed to spin a couple of times over the past few months. It’s been working fine most of the time. Should I still call a technician?
Hi Hunter! If it’s only happened once or twice, it may have been due to a temporary imbalance or power fluctuation. However, if it starts happening more often — or the spin cycle feels weak — it’s a good idea to get it checked early to avoid bigger issues later. We can run a full diagnostic and make sure everything’s working as it should.